United-office 2-in-1 Paper Trimmer User Manual download pdf (Page 7)

GB 7

3. The guillotine arm is locked on the underside of

the cutting unit. To unlock the guillotine arm, pull

the locking latch out to the right to Position A and

then slide the locking latch towards the front to

Position B (Fig. 1).

4. Move the guillotine arm upwards.

5. Place the material to be cut in the required posi

tion under the pressing rail and press the pressing

rail down (Fig. 2).

6. Then use your other hand to move the guillotine

arm down and cut the document (Fig. 2).

7. In order to lock the guillotine arm again after fin

ishing your work, move the guillotine arm down

as far as possible, pull the locking latch at Posi

tion B out to the right and then slide the locking

latch to the rear to Position A (Fig. 3).

Trimmer

Trimmer with integrated cut selector knob

and setting lock.

Cutting function:

- Straight cut

Cutting capacity: max. 10 sheets (80 g / m²)

- Perforation

Cutting capacity: max. 3 sheets (80 g / m²)

- Wave cut

Cutting capacity: max. 3 sheets (80 g / m²)

The blades are accommodated in a protected hous

ing.

1. Place the cutting unit on a stable, level working

base with the trimmer side facing up.

2. Slide the cutting head to one side of the guide rail

3. Turn the left and right-hand rotating knobs to

OPEN. Place the material to be cut under the

guide rail. Then the rotating knobs to LOCK. The

material is fixed and you can cut it.

Note: Hold the material to be cut securely, otherwise

it could shift and be cut inaccurately. The raster and

measuring system on the trimmer's working surface

serve as positioning aids.

4. To complete the cut, press the cutting head down

and slide it along the guide rail to the other side

(Fig. 4).

Note: To prevent a faulty cutting edge, do not run the

cutting head back again but remove the cut material

directly after completing the cut.

Selecting the Type of Cut

The trimmer has three different types of cut available

for selection: straight cut, perforation cut and wave

cut.

1. Slide the lock on the cutting head upwards (Fig.

5).

2. Turn the selector knob until the symbol represent

ing the required type of cut is under the lock (Fig.

5).

3. Press the lock on the cutting head downwards

(Fig. 5).

Replacing the Blade

The blade has four cutting edges (two on each side).

When the quality of the cut is no longer clean, turn the

blade so that one of the unused cutting edges will be

used.

1. Slide the cutting head to one end of the guide

rail.

2. Remove the blade out of the slot from the other

side of the guide rail. Recesses are provided for

this at both sides of the guide rail (Fig. 6).

3. Turn the blade so that one of the cutting edges

not yet used is moved to the cutting position. Lay

the blade back in the slot. When all four cutting

edges of the blade are worn, replace the blade.

Changing a Cutting Head

When the blade of the cutting head is damaged or

worn, the cutting head must be replaced.

1. Remove the end cap of the guide rail from the

base plate (Fig. 7, A) by simultaneously pressing

it in a little at the bottom end and sliding it up.

LB4.pdf 7LB4.pdf 7 15.02.2012 12:08:5715.02.2012 12:08:57

1 2 3 4 5 6 7 8 9 10 11 12 ... 41 42

Comments to this Manuals

No comments

United-office 2-in-1 Paper Trimmer User Manual Page 7

Comments to this Manuals

Related products and manuals for Office Equipment United-office 2-in-1 Paper Trimmer